Sound Heating and Air Conditioning Inc. Blog: Posts Tagged ‘Snoqualmie’

HVAC Q/A: What Is an Electronic Ignition?

Wednesday, March 7th, 2012

Gas furnaces in Tacoma are very complex pieces of equipment. Modern ones in particular are designed to use as little gas as possible, and to recapture as much of the heat generated from burning that gas as can be done safely. One of the many safety and energy-efficient advances in furnace technology in the least twenty years is the electronic ignition.

The Purpose of Electronic Ignition

In older furnaces and boilers, a pilot light would stay lit continuously whenever the heating system needed to be available. That meant continuously burning gas throughout the fall, winter and spring months for those times when heat was needed. It was inefficient and unsafe, especially in older devices that didn’t have safety valves.

Today, furnaces are built with electronic ignitions – small devices that only ignite the gas supply when the thermostat is on. there are two types of electronic ignition used in boilers and furnaces today.

  • Intermittent Pilot – An intermittent pilot is unique in that it releases a spark through an electronic component to the gas pilot, lighting the gas burners.
  • Hot Surface Ignition – Hot surface ignition uses an electronic filament (like a lightbulb) to heat up and ignite the burners when the thermostat calls for heat.

Both devices are designed to use a very small amount of electricity and reduce the amount of gas needed for continuous operation of your furnace.

Safety Benefits of an Electronic Ignition

While gas efficiency was a big part of the transition from pilot lights to electronic ignition, safety was an equally big component. Whereas before, the pilot light was continuously lit, meaning gas was continuously flowing into the furnace, today’s furnaces are essentially off when not in use. This means less of a chance that gas will flow unburned or that the pilot will get dirty or burn too soft, releasing carbon monoxide.

If your furnace or boiler still uses a traditional pilot light, consider having it upgraded to electronic ignition, not just to save gas but to keep your home and family safer.  Call Sound Heating for more information.

Continue Reading

Why Are Clean Filters So Important to AC Efficiency?

Tuesday, February 28th, 2012

Air conditioners cost a lot of money to operate in Seattle – even more when they don’t work at 100% efficiency. So, it is important to perform the various regular air conditioning maintenance tasks that ensure the system uses as little electricity as possible. The first thing on your list (and the easiest) is cleaning those filters.

Keeping Filters Clean

The Department of Energy’s Energy Savers website states that you can reduce your air conditioner’s energy consumption by as much as 15% simply by keeping the air filters clean. Why do they matter so much? Consider the nature of a filter.

The filter on your AC unit is designed to capture any dust, debris and sediment in the air supply. If that dust and sediment was allowed in, not only would it gum up the mechanical workings of the device, it would get into your ductwork and reduce the air quality of your home. So, filters are used to capture such things. However, when a filter gets clogged, the system must work harder to draw the air in. As it works harder, the motor turns faster and more electricity is used.

It takes very little to clog the filter of an AC unit, especially if it is running 24 hours a day for two or three months out of the year. So, it’s best to check your filters once every 30 days regardless of what type of filter you are using.

Which Filters to Check

The main filter on your AC unit should be checked along with any air handler filters and any air cleaner filters you have installed in your system. Another thing to consider is the condition of your home and the area around your outdoor condenser. If you have pets, lots of plants or your condenser is located in a dusty area, you may need to check and change those filters even more often.

Most filters are located along the return length of the ductwork – sometimes in ceiling ducts and walls, though they may also be located in your furnace’s air handler or inside the air conditioning unit. If you have window units or mini splits, the filters are frequently in the unit.

Clean air filters are important for your health, your wallet and the longevity of your AC system. Stay on top of them and you will save money in more ways than you might expect.  Please contact Sound Heating if you have any questions.

Continue Reading

Indoor Air Quality Tips: How Electronic Air Filter Works

Monday, February 6th, 2012

For a long time, the most frequently used kind of air filter in Tacoma has been the mechanical variety. This is the kind you probably think of when you hear the terms air filter, air cleaner or air purifier. They use pleated fibrous filters in-line with an air handler to trap particles in the air before circulating it back out into the home. Many models of these work very well and have for many years. They have the added benefit of being flexible because you can put in whatever filter you need depending on what size particles you need to trap. However, these traditional devices are not the only option. A second kind of air filter exists for trapping particles in the air– one that does not use a fibrous filter that physically snags them out of the air on the way through. These electrostatic, or electronic air filters work in a different way to produce a similar result. The filtering component is still a fibrous sheet, but the difference is that the fibers are made of plastic, which becomes charged when air passes through it and causes friction. (Think something like when you rub a balloon and stick it to the wall.) These friction-charged fibers carry an electronic charge, which attracts the ions in the air around it. These ions — and the particles that they are a part of — get trapped in the fibers and stay out of your air supply. Electronic air filters are generally very good at trapping particles that are 1 micron in size or higher, putting them about on par with a mechanical air filter that carries a MERV rating of 12. The electrostatic method works well for many common household air pollutants, such as dust, pollen, mold and pet dander. As with many ventilation-related decisions, the choice of what kind of air filter is right for you depends on your needs and those of your family. If you are having trouble deciding, then contact Sound HCVA experts with any questions.

Continue Reading

HVAC Tip: Seasonal Air Quality Control

Friday, January 27th, 2012

For people who suffer from seasonal allergies in Seattle, air quality is a key concern. Allergens in the air cause brutal bouts of sneezing, runny nose, itchy eyes and even sinus headaches. Even taking refuge indoors will often not assuage these symptoms, as indoor air is often comparable to outdoor air in terms of allergens and overall quality.

That is, unless you take care to control the seasonal air quality in your home, which can not only help ease the suffering of allergies, but also soothe asthmatics, keep out pollutants and generally promote better overall health.

How do you go about controlling the air quality in your home? To start, try these simple tips:

  1. Vacuum carpets regularly. Use a vacuum with a HEPA filter and invest in some allergen suppressing bags.
  2. Keep your vents clean. This is also a good maintenance practice to lengthen the life of your ventilation equipment.
  3. Dust hard surfaces and wash bed linens weekly.
  4. Install HEPA filters in your ventilation system, such as in air conditioners or other air handler units. Use a higher rated filter to keep out more allergens and pollutants.
  5. Invest in and use an air purifier. Again, make sure to get one with a HEPA filter.
  6. Have your home tested for radon and carbon monoxide. Have smoke, carbon monoxide and radon detectors working properly at all times.
  7. Use a humidifier to keep overly dry air from irritating sinus passages.
  8. Keep doors and windows closed tight, especially during allergy season(s).

By taking charge of the air quality in your Seattle home, you also take control of a measure of your family’s health. Some of these measures require at least a bit of an investment – for example, higher rated HEPA air filters are often more expensive and need to be changed more frequently – but the benefits to your well being and that of your family are clearly well worth it.

Continue Reading

5 Reasons to Replace the Furnace in Your Buckley Home

Wednesday, January 4th, 2012

Many Buckley homes are heated with furnaces, since they generally provide safe and efficient heat.  Furnaces have also improved dramatically over the years as manufacturers find ways to make them more efficient. Even if your furnace has been reliable for many years, it may be worth the money to replace your old furnace with a newer, more efficient model.

Here are five major benefits to upgrading your Buckley furnace.

1. Lowering Your Utility Bills

Whether you realize it or not, your current furnace could be costing you more than it should in heating bills. If your furnace is 15-20 years old, it’s probably not heating your home as efficiently as the newer models with higher AFUE ratings. Even if your heating system has been replaced within the last ten years, the technology has advanced enough to consider an upgrade.

2. Fewer Repairs

Repair costs can add up if you are constantly repairing your furnace. Routine maintenance for your furnace can help reduce the need for repairs, but as furnaces age, they tend to need more repairs and replacement parts. If you need frequent repairs for your furnace, it may be time to replace it with a newer one.

3. More Consistent Heat

While maintaining consistent temperatures throughout your home involves several factors, such as insulation and thermostat control, your furnace could also be the reason you aren’t getting enough heat to all parts of the house. If some rooms are colder than others, or if your heating bills have recently gone up, it may be time for a furnace replacement.

4. Reduce the Chances of a Breakdown

When a furnace breaks down, it not only leaves you without heat, but it is also a major expense. Budgeting for a new furnace before it breaks down will put less financial burden on you than needing an emergency furnace replacement. Newer model furnaces are also more reliable and less likely to give you problems if maintained properly.

5. Safety

There’s higher potential for safety concerns with older or poorly maintained furnaces. In addition to fire hazards, carbon monoxide poisoning is another serious threat. When the heat exchanger stops working because it’s corroded or faulty, carbon monoxide can leak into the home. If you’ve had your furnace for more than 20 years, it could create safety hazards that you may be unaware of.

No matter how long you’ve had the furnace in your Buckley home, it’s always wise to speak with a qualified HVAC technician about furnace upgrades, particularly if you have expensive heating costs. Call Sound Heating & Air Conditioning Inc. today to talk with one of our heating experts about furnace upgrades.

Continue Reading

What Happens if My Heat Pump Loses Power? A Question from Edgewood

Monday, November 7th, 2011

One of the advantages of having a heat pump in your Edgewood home is that they operate on electricity, so you don’t need to worry about having maintaining a supply of fuel to keep yours running. Where a furnace or boiler might call for you to purchase supplies of oil or natural gas, and a wood stove means keeping potentially messy firewood around, a heat pump runs cleanly on electricity.

Heat pumps are good at using electricity, too. They are often able to produce heat energy that can be as much as three times the electricity they draw to produce it. This means not just convenience, but also a big savings, just by virtue of using electrical power.

The risk there, of course, is that if and when the power goes out, so does the heat pump. That means when a big winter storm drops a tree on the local power line, things can get cold inside mighty quickly. For these situations, you should have a backup heating solution on hand to keep everyone comfortable in the short term. And, as a responsible homeowner, you likely already have this taken care of.

But what happens when the power comes back on? Can you just fire your heat pump right back up without missing a beat?

The short answer is “no.” You should not do that, for at least two reasons. First of all, after any power outage, you should always take care to turn on appliances gradually over a period of time rather than all at once in order to avoid a spike in demand at the power company, which can blow a grid. That’s just a general tip.

Specific to heat pumps, though, there is a unique concern. If the heat pump loses power for more than 30 minutes, the refrigerant can get too cold to flow properly, so turning it right back on can cause the whole thing to conk right out. Instead, do the following:

  1. Make sure the heat pump is off. You can do this during the power outage.
  2. Once power comes back on, turn the heat pump to the “Emergency Heat” setting. This will allow the compressor to warm up slowly and get the refrigerant warm enough to start flow freely again.
  3. Wait. The time you need to wait varies depending on the size and manufacturer of your heat pump, so refer to the manual. In general, you should wait at least 6 hours.

After this process, your heat pump should be ready to resume normal operation without issue.

Continue Reading

Heat Pump Maintenance: Some Pointers from Seatac

Friday, November 4th, 2011

Heating and cooling your Seatac home is a priority. You need your home and family to be comfortable all year round, so you either got or are considering a heat pump. These machines are great because under the right circumstances, they are essentially all-inclusive and incredibly efficient solutions for all your home heating and cooling needs.

Notice the “under the right circumstances” part. A number of things have to be considered when choosing a heat pump, such as the climate and the size of your home. But these are not the only circumstances that influence how well your heat pump works for you. Proper maintenance is a vital component of heat pump ownership, ensuring that you get the best performance out of your heat pump for the longest time possible.

A major part of properly maintaining any machine is to keep it clean. A heat pump is no exception. Dirt and dust can affect the efficiency of your heat pump, as well as speed up corrosion problems. Keep the compressor and coils clean. Check them monthly or so and remove any accumulated dirt. Also, consistently check and change filters according to the manufacturer’s recommendations.

Simple cleaning is an easy and effective first step to heat pump maintenance, but there are some things that you just won’t be able to do on your own. For more intensive maintenance, it is best to call in a professional for an annual inspection.

During a routine maintenance check of your heat pump, a technician will inspect the whole heat pump system for problems. He will clean the compressor and coils, tighten any connections that may have loosened up and change the filters as needed. In addition, a skilled technician will be able to detect any early signs of trouble and make necessary repairs to prevent break downs. These small repairs can prevent big problems later on, thereby preventing some serious discomfort and a possible big expense.

If you are considering a heat pump as a heating and cooling solution for your home, great. If you have already decided on one and had it installed, congratulations on making a smart decision. Now, make another smart decision to protect that investment by keeping your new heat pump properly maintained.

Continue Reading

Plants & Indoor Air Quality: A Tip from Tacoma

Monday, October 24th, 2011

In our Tacoma elementary school, we were taught that plants are the “lungs of the Earth.” They remove carbon dioxide from the air and release oxygen, which is great because it is the exact opposite of our respiratory process. They also clean the air in the process, like natural air pollution scrubbers, improving the quality of the air around them.

Given this, it’s not surprising that people have sought to harness the respiratory power of plants to improve air quality in their homes. One study by the National Aeronautics and Space Administration (NASA) in the 1980s even identified the best plants for improving indoor air quality.

This seems like great news for people who suffer from asthma or allergies, or who just want a natural way to purify the air in their homes. However, plants are not without their drawbacks. It is not a simple as to just bring a plant into the home. A plant is really an entire ecosystem, with many other organisms latched on for dear life. There are bacteria in the soil, for one, and there may be bugs or fungi in the soil or on the plant that you can’t even see.

Most of these are harmless, but not always. The fungus can be a problem, for example, if the spores get into the air. This can make allergies and asthma worse, not better.

That doesn’t mean you have to toss out that nice spider plant or Boston fern in the garbage, however. After all, it is probably doing a great job of filtering out some inorganic pollutants, it’s increasing the oxygen concentration of the room and it looks nice. Instead of getting rid of it, just give it a partner.

Adding an air cleaner like a fan with a filter can help purge the organic gunk that may be coming from the plant, while the plant is taking care of the other stuff. The result is cleaner, better air, which can be a relief to asthma and allergy sufferers.

Continue Reading

Benefits of Replacing Your Furnace in Fife

Monday, October 17th, 2011

You are about to make one of the largest purchases in your life – a new furnace for your Fife home. Maybe your old furnace is on life support and needs immediate replacement or you are looking for a better, more efficient furnace that will raise the comfort level of your home while reducing utility bills and carbon emissions.

If the furnace in your basement, crawl space, or attic is 15-20 years old, it may be a single-stage 80% percent efficient model, which doesn’t meet the higher efficiency standards of today’s models. It uses more energy, i.e. gas, oil, or electricity, to operate. And a single-stage furnace does not always provide even heating to all rooms in the home, based on the varying winter weather conditions. There may be large temperature variations from room to room.

Your new furnace will likely be more efficient and environmentally friendly than the one it is replacing – which are the two biggest benefits to replacing an old furnace. So, let’s take a closer look at these benefits, which link energy efficiency to the latest technology – namely two-stage furnaces and variable speed motors.

Two-stage furnaces start out by running in a first stage, which uses less than 70% of its capacity. This stage works well on moderate winter days. On colder days, the furnace will meet your extra heating demand by adjusting to the second stage in the heating cycle. Since the furnace spends most of its time operating in its lower capacity (first or single stage), it burns less fuel than a traditional furnace that always runs at full capacity and then shuts off when heating demand is met. You will see lower utility bills and a shorter payback period on your new furnace investment.

Variable-speed motors can actually save you money on your energy bill as they consume less electricity than standard motors. Variable speed furnaces save you money by having a higher SEER rating. SEER is the abbreviation for seasonal energy efficiency ratio. The higher the SEER, the more energy efficient the unit. The low operating costs of a variable speed furnace can allow you to run your furnace blower. With the low operating costs of the variable-speed furnace you can constantly run your blower without the worry of driving up your utility bill, allowing for continuously filtered air.

The U.S. government, as well as local governments are making it more tempting for homeowners like you to purchase new energy efficient furnaces, too. Government agencies have been offering tax credits to homeowners who switch to energy-efficient appliances, including heating and cooling products. Utility companies also offer rebates to homeowners who wish to lower their utility bills by using high-efficient appliances. Chances are, your local utility has some type of rebate program in place.

And when you shop for a new furnace, look for add-on equipment such as electronic air filters and programmable thermostats. Each will raise the comfort level you will be enjoying from your new furnace.

Continue Reading

Things You Should Have Inspected: A Guide From Snoqualmie

Wednesday, September 21st, 2011

Life would be great in Snoqualmie if we could just depend on things to work and last without requiring any sort maintenance or upkeep. Unfortunately, that is not the case. As good as modern manufacturing and engineering are, our devices, appliances and machines still need attention in order to stay in peak condition.

The Body Is a Machine

To illustrate this, think about the human body. We put a lot of wear and tear on ourselves, which can lead to minor illnesses, injuries and the like, especially when combined with the effects of aging. One way we attempt to stay ahead of the game is to get an annual physical. Once a year, we pay a visit to our doctor to make sure everything is in tip top shape. He checks everything out, lets us know what’s going on, helps us treat anything that may be acting up and then off we go, ready to go for another year.

And So Is Your Furnace

Likewise, your furnace needs annual attention as well. Although newer electrical furnaces can go up to three years without regular maintenance, gas and oil models should be inspected every year, as should older systems. During an annual inspection, an HVAC professional will:

  • Clean out fuel lines, keeping every flowing freely and efficiently.
  • Check for parts that are wearing out or need to be replaced.
  • Clean and inspect the heating ductwork as well as the vents.

These simple and routine maintenance tasks can extend the life of your furnace by years, keeping your home warm and your heating costs low.

The Best Time for Inspection

The best time to get your furnace inspected is in the late summer to fall months. Although you may still be trying to squeeze every bit of enjoyment from those last warm days, the cold weather comes not far behind, and you will want your furnace ready when that happens. A fall inspection ensures that your furnace will be all set when those temperatures start to drop, so your family won’t have to tolerate any chilly nights.

Annual inspections and maintenance are important for health and longevity, both for you and your furnace. You can even schedule your physical and your furnace inspection around the same time so you don’t forget. Make an appointment for your car while you’re at it, too. That makes three things you won’t have to worry about during those cold winter months.

Continue Reading